
G2 Throttle & Brake (Elite)
Pure mechanical precision.
Launch price until 4 January 2027. Regular price $949 from 5 January 2027.
Pre-orderEstimated shipping: approx. 18 December
Measure the driver. Not the pedal. A brake that firms up like a race car's, a zero-friction throttle and a clutch that lets go like the real thing, with a load cell on every pedal.
Also in the Sport edition, $599 →Key features
- ProgressiveMechanical brake, no hydraulics
- Zero frictionThrottle on a ball bearing
- Real clutch feelForce drops at the end of the stroke
- Load cellOn every pedal, part of the frame
- Steel springsSame force hot or cold
- Adjust on the rigPreload, brake curve, face height and tilt
- CNC-machined facesSolid 6061, carbon grey, diamond grip
- Hydraulic dampersFitted to every pedal, adjustable
- Measured curvesForce graph for every brake setting
- 24-bitLow-noise pedal controller
- European UnionMade in
- 3 yearsLimited warranty (fitted dampers 1 year)







US orders start shipping approx. 18 December
Estimated date when orders start leaving our warehouse. Delivery time depends on your location.
Measure the driver. Not the pedal.

A brake that feels the same on every lap
200 kgload cell that carries the pedal arm
A tie rod and bell crank make the force rise faster the further you press, so the pedal firms up under your foot the way a race car brake does. No oil, no seals, nothing to bleed.
- Progressive tie rod and bell crank linkage
- Crank CNC-machined from solid 6061 aluminium
- Adjustable curve, with measured force graphs

Steel springs: the same force, hot or cold
2 springsin the box, the red one roughly doubles the force
Elastomers push back differently on release than on press, and soften as they warm. A steel spring gives the same force at the same travel, in the first ten minutes and the last.
- Steel compression springs, no elastomers
- Blue fitted, red included

A zero-friction throttle
10 kgload cell in the pedal arm
The back of the spring sits in a swing bracket that turns on a ball bearing, so the spring and its shaft pivot with the pedal and the spring is always pressed in a straight line, never bent or binding, even with a lot of preload. No notch at the start of the travel: the pedal moves the instant you touch it and follows when you lift.
- Ball-bearing swing bracket
- Polished 304 stainless shaft in a low-friction POM bearing
- Tool-free preload knob

A clutch that feels like a real car’s
80 kgload cell
The force rises, then falls away at the end of the stroke, as it does with a diaphragm spring. Your foot finds the same reference point for every start and downshift.
- Geometry modelled on a diaphragm-spring clutch
- Rear pivot held on both sides, on ball bearings

A hydraulic damper for a steadier pedal
Adjustabledamping, held by a locking screw
The damper resists more the faster you press, so trail braking becomes a controlled release. Elite has one on every pedal. On Sport every arm is prepared for the G2 Damper Upgrade Kit.
- Runs on bearings: adds damping, not friction
- Fits the throttle, brake or clutch
Rigid build, tool-free adjustment, clean signal

The load cell is part of the frame
On every G2 pedal the load cell is a load-bearing part. Fewer parts between foot and sensor means less to flex and nothing to drift out of line.

Tool-free preload on every pedal
Spring preload on all three pedals is set by a machined aluminium knob, by hand, with the pedals bolted down.

Pedal faces adjust for height and tilt
The face sits on a two-screw mount. Slide it along the 27 mm slots to set its height, and set its tilt so it meets your sole flat.

3 mm steel plate, built not to flex
A 3 mm steel frame on thick steel feet holds the pedal still under your hardest stop. Tilt locks into fixed holes, so left and right always match.

CNC-machined aluminium faces on both editions
Sport faces are 2 mm aluminium with CNC-machined edges, sandblasted and black anodised. Elite faces are machined from solid 6061, carbon grey anodised, fixed from the sides with a diamond grip on the brake and clutch.

A 24-bit controller for a clean signal
All three load cells are read by a low-noise amplifier and a 24-bit converter. VRS One handles calibration, maximum brake force and dead zones.
G2 Pedals Specs, Box Contents & Editions
Brake
- 200 kg load cell that carries the pedal arm
- Progressive tie rod and bell crank linkage, no oil or seals
- One-piece CNC-machined 6061 aluminium crank
- Steel springs, no elastomers. Blue fitted, red included
- Tool-free CNC preload knob
Throttle
- 10 kg load cell, bolted into the arm
- VRS-engineered throttle spring, custom-manufactured for VRS, on a polished stainless centre rod
- Ball-bearing swing bracket: the spring and shaft pivot with the pedal, so the spring never binds
- Polished 304 stainless shaft in a low-friction POM bearing
- Tool-free CNC preload knob with a wide range
Clutch
- 80 kg load cell
- Race car force curve: rises, then drops at the end
- Clevis linkage with roller
- Rear spring pivot held on both sides, on ball bearings
- Tool-free CNC preload knob
All pedals
- 3 mm laser-cut steel frame, deep black powder coat
- Shielded ball bearings on the pivots
- Dual end stops, 70 and 90 Shore, on hex spacers
- 5 tilt positions, about 20°
- Pedal face height (27 mm) and tilt adjustment
- Faces curved to R400. Sport: 2 mm aluminium, CNC-machined edges, sandblasted, black anodised. Elite: CNC-machined from solid 6061, carbon grey anodised, diamond grip on brake and clutch
Electronics and software
- VRS Pedal controller, all-aluminium, 3 pedal ports
- 24-bit ADC, 14.3 effective bits
- USB, 1.6 m cable
- VRS One: calibration, maximum force, dead zones, firmware updates
Mounting
- 4 × M6 per pedal, slotted, 70 × 120 mm pattern
- Same footprint for throttle, brake and clutch
- 87 mm wide per pedal, 92.5 mm with a damper
- Optional G2 Baseplate
Compatibility
- PC with a USB port, Windows 10 or above
- Any game that supports controllers
- The clutch uses the Pedal controller from the Throttle & Brake set
Measure the driver. Not the pedal.
A load cell on every pedal, a progressive mechanical brake, a zero-friction throttle and steel springs that feel the same on lap 100 as on lap 1. Throttle & Brake and Clutch, in Sport and Elite. Made in EU, with a three-year limited warranty.